山東創圖建筑裝飾工程有限公司
13165128506
您當前位置: 如何解決防火板加工時出現的爆邊問題？
來源：http://qdlaojing.cn/ 日期：2021-05-07 發布人：admin
如何解決防火板加工時出現的爆邊問題？
How to solve the problem of edge burst in the processing of fireproof board?
(一)、出現上面爆邊
（1） The top edge appears
1、主鋸片太鈍，鋸齒太少
1. The main saw blade is too blunt and the saw teeth are too few
2、主鋸片高出板材太少
2. The main saw blade is too little higher than the plate
3、板材質量太差，會很快鈍鋸片
3. If the quality of the plate is too poor, the saw blade will be blunt soon
4、重新更換鋸片
4. Replace the saw blade again
5、升高主鋸片
5. Raise the main saw blade
6、選用雜質少、質量高的板材
6. Select the plate with less impurities and high quality
(二)、出現下面爆邊(鋸后的板材)
（2） There is edge burst below (sawn board)
1、副鋸片太鈍
1. The saw blade is too blunt
2、副鋸寬度不夠、太窄
2. The width of the auxiliary saw is not enough or too narrow
3、主、副鋸片中間線不重合
3. The middle line of the main saw blade and the auxiliary saw blade does not coincide
4、重新更換鋸片
4. Replace the saw blade again
5、換鋸片或增加鋸片厚度
5. Change saw blade or increase saw blade thickness
6、重新調整副鋸左右位置
6. Readjust the left and right position of the auxiliary saw
(三)、有燒焦的痕跡(鋸后板材上)
（3） There are burning marks (on the sawn plate)
1、合金鋸片太鈍，鋸片上鋸齒太多
1. The alloy saw blade is too blunt and there are too many teeth on the saw blade
2、轉速過高或進料太慢
2. Too high speed or too slow feeding
3、更換鋸片，選擇適當?shù)匿徠?/div>
3. Replace the saw blade and select the appropriate one
4、選擇適當?shù)霓D(zhuǎn)速和進料速度
4. Select the appropriate speed and feeding speed
(四)、在鋸切時有工件被副鋸頂起來的現象
（4） During sawing, the workpiece is jacked up by the auxiliary saw
1、副鋸片太鈍
1. The saw blade is too blunt
2、副鋸片升得太高
2. The auxiliary saw blade rises too high
3、更換鋸片
3. Replace the saw blade
4、適當降低副鋸片高度
4. Reduce the height of the auxiliary saw blade appropriately
(五)、中間貼面板爆邊
（5） Edge burst of middle panel
1、板材較厚，每塊微彎不平整，上下面互疊一起后產生縫隙
1. The plate is thick, each piece is slightly bent and uneven, and the upper and lower parts are overlapped to form a gap
2、機械壓料的氣缸壓力不夠
2. The cylinder pressure of mechanical pressing is not enough
3、工件板面有條紋(凹凸)也會爆邊
3. The work piece plate surface has the stripe (concave convex) also can burst the edge
4、工作鋸切時少壓2-3塊板材
4. Press 2-3 pieces less when sawing
5、鋸切板材時進刀速度適當調慢適切認可
5. When sawing the plate, the feed speed should be adjusted to be appropriate
6、檢查鋸片是否不鋒利，及時修磨刃口
6. Check whether the saw blade is not sharp, and repair the edge in time
感謝您的閱讀，希望以上內容對您有所幫助，如您想了解更多精彩內容請點擊我們的官網：富美家山東總代理http://qdlaojing.cn。
Thank you for your reading. I hope the above content will be helpful to you. If you want to know more wonderful content, please click our official website: fumika Shandong general agent http://qdlaojing.cn .
分類導航
Related products相關新聞
- 探秘耐火板界的 “全能選手”：解析富美家產品的獨特魅力2025-07-01
- 富美家室內門：解鎖家居 “門道” 的獨特密碼2025-06-26
- 富美家HPL可以接受到多高的溫度？2025-06-20
- 探索富美家美耐板為什么值得選擇？2025-06-18
- 富美家衛生間隔斷：用科技重新定義“方寸之間的品質”2025-06-16
- 富美家衛生間隔斷核心材料技術解析2025-06-11
- 富美家色麗石適用場景解析：從材料特性到應用領域的科普指南2025-06-09
- 挑選衛生間隔斷質量怎么檢查？2025-06-03
- 探秘耐火板誕生記：從自然饋贈到匠心杰作2025-05-26
- 富美家HPL怎么才能成為“六邊形戰士”的2025-05-22
產品銷售熱線：13165128506
技術方案咨詢：18560211715 18663705616
倉庫地址：山東省濟南市天橋區金鑫產業園303倉庫